Custom castings from your drawings or samples. Send your requirements for a quotation.Request a Quote
Jiangkai Casting logoJK CastingDrawing-based OEM metal parts

Material reference

CF8M Stainless Steel (Cast 316): Equivalents, Composition and Properties

CF8M is an austenitic cast stainless steel grade in ASTM A351 and A743, the cast counterpart of wrought 316: carbon up to 0.08% and 2.0–3.0% molybdenum. This page compares it with 1.4408, ZG07Cr19Ni11Mo2 and 12Х18Н12М3ТЛ and lists its composition and properties.

JK Casting · Buyer resource · Updated 16 November 2026

What CF8M is

CF8M is the cast counterpart of 316 stainless steel. It is defined in ASTM A351 (castings for pressure-containing parts) and also listed in ASTM A743 (general-service corrosion-resistant castings). The M stands for molybdenum, 2.0–3.0%, which improves resistance to pitting compared with CF8.

CF8M equivalents: China, Europe and Russia

Scroll sideways to see the whole table

Approximate comparison. The standard on the drawing governs; substitution needs buyer approval.
StandardGradeNote
Wrought counterpart316Composition limits and structure differ from the cast grade
GB/T 2100-2017 (China)ZG07Cr19Ni11Mo2Nearest Chinese corrosion-resistant casting grade
EN 10213 (Europe)1.4408 (GX5CrNiMo19-11-2)Carbon ≤0.07%, molybdenum 2.0–2.5%
ГОСТ 977-88 (Russia)12Х18Н12М3ТЛNearest by composition; titanium-stabilised, carbon up to 0.12%, molybdenum 3.0–4.0%

These equivalents are approximate, not identical materials. Composition limits, test methods and heat treatment differ between standards. The standard named on the drawing governs, and any substitution needs the buyer’s written approval.

CF8M chemical composition

Scroll sideways to see the whole table

% by mass; single values are maximums.
ElementCF8M (ASTM A351)1.4408 (EN 10213)
Carbon (C)0.080.07
Silicon (Si)1.501.50
Manganese (Mn)1.501.50
Phosphorus (P)0.0400.040
Sulfur (S)0.0400.030
Chromium (Cr)18.0–21.018.0–20.0
Nickel (Ni)9.0–12.09.0–12.0
Molybdenum (Mo)2.0–3.02.0–2.5
Copper (Cu)–0.50

CF8M mechanical properties

Scroll sideways to see the whole table

Minimum values unless a range is shown.
GradeTensile, MPaYield, MPaElongation, %
CF8M (ASTM A351)485205 (0.2%)30
1.4408 (EN 10213)440–640210 (Rp1.0)30
12Х18Н12М3ТЛ (ГОСТ 977-88)44121625

ASTM A351 covers austenitic castings for pressure-containing parts; ASTM A743 lists the same grade names for general-service corrosion-resistant castings. Tensile values are minimums from ASTM A351; elongation is measured over 50 mm. In ksi: tensile 70, yield 30.

EN 10213 values are for the solution-annealed condition (+AT) and wall thicknesses up to 150 mm. EN 10213 states a 1% proof strength (Rp1.0) for austenitic grades, which is not the same measure as the ASTM 0.2% yield strength.

Heat treatment and welding

Heat treatment. ASTM A351 requires these grades to be solution annealed at 1040 °C (1900 °F) minimum, then quenched in water or rapidly cooled by other means. Weld repairs are made with procedures and welders qualified to ASTM A488.

ГОСТ 977-88 gives quenching from 1100–1150 °C in water for 12Х18Н12М3ТЛ. Where parts are welded and corrosion resistance next to the weld matters, the low-carbon grade CF3M (cast 316L) is often specified instead.

How JK Casting makes CF8M castings

JK Casting reviews every stainless steel casting part by part. Send the drawing, the grade with its standard and any corrosion or test requirements, and JK confirms the casting route, investment casting or sand casting, before quoting. Investment castings made in-house weigh up to about 20 kg each. Castings are supplied raw or machined, and JK machines only the castings it makes. Each drawing is quoted separately, with tooling and unit price on separate lines.

Related pages: Cast stainless steel grades chart · Investment casting · Steel castings · What to put on a casting drawing · Send a drawing for quotation

Frequently asked questions

Is CF8M the same as 316?

No. CF8M is the cast counterpart of wrought 316. Its composition limits differ, for example chromium 18.0–21.0% in ASTM A351, and the cast structure normally contains some ferrite. If a drawing for a cast part names 316, agree the casting grade in writing.

What is the difference between CF8M and CF3M?

CF3M allows at most 0.03% carbon against 0.08% for CF8M, and a slightly wider nickel range. It is the cast counterpart of 316L and is chosen for welded parts where corrosion resistance next to the weld matters.

What is the European equivalent of CF8M?

EN 10213 1.4408 (GX5CrNiMo19-11-2) is the usual counterpart. It allows up to 0.07% carbon and 2.0–2.5% molybdenum, a narrower range than CF8M’s 2.0–3.0%.

What is the Russian equivalent of CF8M?

ГОСТ 977-88 12Х18Н12М3ТЛ is the nearest by composition, but it is titanium-stabilised, allows up to 0.12% carbon and has 3.0–4.0% molybdenum, so it is not a direct equivalent.

Standards referenced: ASTM A351/A351M; ASTM A743/A743M; EN 10213; GB/T 2100-2017; ГОСТ 977-88.