What LCB is
LCB is the carbon steel grade of ASTM A352, which covers ferritic and martensitic steel castings for pressure-containing parts intended primarily for low-temperature service. The standard lists −46 °C (−50 °F) as the usual minimum impact test temperature for LCB: the lowest temperature at which the material ordinarily must meet the impact requirements.
LCB compared with WCB
Scroll sideways to see the whole table
| Grade | Standard | Min. yield, MPa | Tensile, MPa | Min. elongation, % | How it compares |
|---|---|---|---|---|---|
| LCB | ASTM A352 (USA) | 240 | 450–620 | 24 | Reference grade |
| WCB | ASTM A216 (USA) | 250 | 485–655 | 22 | Same carbon and manganese limits, higher tensile range, no impact requirement in A216 Table 2 |
| GP240GH | EN 10213 (Europe) | 240 | 420–600 | 22 | Similar minimum yield, lower tensile range |
These equivalents are approximate, not identical materials. Composition limits, test methods and heat treatment differ between standards. The standard named on the drawing governs, and any substitution needs the buyer’s written approval.
LCB chemical composition
Scroll sideways to see the whole table
| Element | Content, % by mass |
|---|---|
| Carbon (C) | ≤0.30 |
| Manganese (Mn) | ≤1.00 |
| Phosphorus (P) | ≤0.04 |
| Sulfur (S) | ≤0.045 |
| Silicon (Si) | ≤0.60 |
| Nickel (Ni) | ≤0.50 |
| Chromium (Cr) | ≤0.50 |
| Molybdenum (Mo) | ≤0.20 |
| Copper (Cu) | ≤0.30 |
| Vanadium (V) | ≤0.03 |
Nickel, chromium, molybdenum, copper and vanadium are residual elements with a total of 1.00% maximum. More manganese is allowed when carbon is below its maximum, up to a limit set in the standard.
LCB mechanical properties
Scroll sideways to see the whole table
| Property | Requirement |
|---|---|
| Tensile strength, MPa | 450–620 |
| Minimum yield strength, MPa | 240 |
| Minimum elongation, % | 24 |
| Minimum reduction of area, % | 35 |
In ksi: tensile 65–90, yield 35. Charpy impact energy values are set in Table 2 of ASTM A352; state the required test temperature and energy on the drawing or purchase order.
Heat treatment
Heat treatment. ASTM A352 requires ferritic castings such as LCB to be supplied normalised and tempered, or liquid quenched and tempered. Liquid quenching is normally needed to meet the properties in heavier sections.
How JK Casting makes LCB castings
JK Casting makes carbon steel castings to customer drawings in Gaomi, Shandong, China. Parts are sand cast, including shell moulding in resin-coated sand, or made by lost-wax investment casting; investment castings made in-house weigh up to about 20 kg each. Castings are supplied raw or machined, and JK machines only the castings it makes. Each drawing is quoted separately, with tooling and unit price on separate lines.
For a quotation, send the drawing with the full grade designation and standard, the heat treatment condition and any tests the part needs. Material records such as EN 10204 3.1 certificates are provided when agreed for the order.
Related pages: Steel castings · Investment casting · Sand casting · What to put on a casting drawing · Send a drawing for quotation
For LCB parts, state the impact test temperature and energy required; these are reviewed with the drawing before quoting.
Frequently asked questions
What is ASTM A352 LCB?
The carbon steel grade of ASTM A352, the specification for steel castings for pressure-containing parts in low-temperature service. Its usual minimum impact test temperature is −46 °C (−50 °F).
What is the difference between LCB and WCB?
Both allow up to 0.30% carbon and 1.00% manganese. LCB has a lower tensile range (450–620 MPa against 485–655 MPa) and higher minimum elongation (24% against 22%), and it is impact tested at a low temperature.
At what temperature is LCB impact tested?
ASTM A352 lists −46 °C (−50 °F) as the usual minimum test temperature for LCB. The energy values are set in Table 2 of the standard; state the required values on the order.
Standards referenced: ASTM A352/A352M-21; ASTM A216/A216M-21; EN 10213.
